burgess
Member
Registered: 22nd Feb 04
Location: Norton, North Yorkshire
User status: Offline
|
posting on behalf of a mate please email/call him for further pics/questions
ring andy 07917765605 or email andyblack2001@yahoo.co.uk
this is far from standard
2.1 block never been run after new pistons/rebore
Fitted with accralite pistons with deep valve pockets
New shell bearings
dipped in acid so its bright cast (no rust)
New oil pump boxed
New timing belt kit with idlers boxed
lightened and balanced flywheel
lighty used clutch
Crank polished.

Cylinder head. not porous!
Needs valves grinding in and new stem seals
Three rocker fastners need rethreading.
Standard camshafts
New full gasket set.
DCOE 45 webers
Inlet manifold
throttle linkages
Air filters fuel pump+filter/reg


DTA 3D fully mappable ignition
computer software
USB lead
user manual
Coil pack
dizzy blanking plate

F20 Gearbox
New shaft seals fitted
Painted silver
taking offers on everything if enough interest its worth at least £1600 as a package and should be good for well over 200bhp
the pistons alone cost £450 never mind carbs etc etc
any questions please call andy he is located in scarborough and is willing to post some of the bits if theres enough interest
[Edited on 15-08-2005 by burgess]
[Edited on 15-08-2005 by burgess]
[Edited on 09-10-2005 by burgess]
|
burgess
Member
Registered: 22nd Feb 04
Location: Norton, North Yorkshire
User status: Offline
|
.
|
burgess
Member
Registered: 22nd Feb 04
Location: Norton, North Yorkshire
User status: Offline
|
bttt
|
Rza_2002
Member
Registered: 2nd Sep 03
Location: Fife
User status: Offline
|
e-mail sent
|
burgess
Member
Registered: 22nd Feb 04
Location: Norton, North Yorkshire
User status: Offline
|
cool might be better to give him a call!
he can work a pc but only just lol
|
burgess
Member
Registered: 22nd Feb 04
Location: Norton, North Yorkshire
User status: Offline
|
ttt
|
Graeme
Premium Member
Registered: 26th Jul 04
Location: Northampton
User status: Offline
|
dont suppose he has got a powercap or ecotec adaptor plate and pipe at all?
|
burgess
Member
Registered: 22nd Feb 04
Location: Norton, North Yorkshire
User status: Offline
|
no it is on carbs so no injection at all needed
|
drunkenfool
Member
Registered: 7th Feb 03
Location: Hereford Drives: Audi R8 V8
User status: Offline
|
Very interested in the bottom end, pistons, oil pump, timing belt kit, crank and flywheel.
|
drunkenfool
Member
Registered: 7th Feb 03
Location: Hereford Drives: Audi R8 V8
User status: Offline
|
oh and the dizzy blanking plate too!
|
BeArDy
Member
Registered: 7th Aug 00
Location: Manchester
User status: Offline
|
Very Interested in the DTA stuff.......
DTA 3D fully mappable ignition
computer software
USB lead
user manual
Coil pack
dizzy blanking plate
|
burgess
Member
Registered: 22nd Feb 04
Location: Norton, North Yorkshire
User status: Offline
|
please get in touch with andy by phone thanks!
|
burgess
Member
Registered: 22nd Feb 04
Location: Norton, North Yorkshire
User status: Offline
|
EVERYTHING HAS NOW GONE!
[Edited on 09-10-2005 by burgess]
|