corsasport.co.uk
  Not logged in [Login - Register]  
You Are Not Registered Or Not Logged In  

Corsa Sport » Message Board » General Chat » well, start one job end up finding a few others


New Topic
New Poll 		  Subscribe | Add to Favourites

You are not logged in and may not post or reply to messages. Please log in or create a new account or mail us about fixing an existing one - register@corsasport.co.uk

There are also many more features available when you are logged in such as private messages, buddy list, location services, post search and more.


Author well, start one job end up finding a few others
Adam-D
Member
Registered: 11th May 02
Location: Cheshire
User status: Offline
18th Mar 06 at 17:15   View User's Profile U2U Member Reply With Quote
handbrake needed a little adjustment, "i like no more than 3 clicks"

so i adjust it jack the back up to see if its binding it is a little so i let it off a bit

then i check the wheel itself

bollocks wheel bearing has play
both side's
so i check the front and need new pads

so after doing a handbrake i now need
2 rear bearings, shoes, cylinder and drums < might aswell kill every bird with 1 stone as its all original stuff
front disks and pads and new caliper seal kits for my new caliper's

woooo
bugger
jamesvalver
Member
Registered: 21st Feb 03
Location: Bury St Edmunds, Suffolk
User status: Offline
18th Mar 06 at 17:17   View User's Profile U2U Member Reply With Quote
rear bearings can be re-tightened mate
Adam-D
Member
Registered: 11th May 02
Location: Cheshire
User status: Offline
18th Mar 06 at 17:20   View User's Profile U2U Member Reply With Quote
there not noisy, just have a bit of play
hmmm,. ill look into that
Adam-D
Member
Registered: 11th May 02
Location: Cheshire
User status: Offline
18th Mar 06 at 17:21   View User's Profile U2U Member Reply With Quote
on a plus note i found i have the door loom to have electric heated mirrors
but the in car side of the loom there is fuck all

ahwell

but i did manage to put new std mirrors on and ditch the combo huge ones

[Edited on 18-03-2006 by Adam-D]
jamesvalver
Member
Registered: 21st Feb 03
Location: Bury St Edmunds, Suffolk
User status: Offline
18th Mar 06 at 17:21   View User's Profile U2U Member Reply With Quote
in that case just nip them bak up again. they should have a little bit of play in them because of the sideways forces on them round corners
mav
Member
Registered: 19th Jun 01
Location: Scotland
User status: Offline
18th Mar 06 at 17:44   View User's Profile U2U Member Reply With Quote
Unlucky always the same though..

I had my rear bearing tightened up in old Xe
Adam-D
Member
Registered: 11th May 02
Location: Cheshire
User status: Offline
18th Mar 06 at 18:13   View User's Profile U2U Member Reply With Quote
so its ok to just tighten them then good stuff

i also changed the pollen/cabin filter
no car i have ever owned has ever ever had this changed ever
there always black as fuck
its done now anyway
Joe
Member
Registered: 20th Jun 04
Location: Hesketh Bank, Lancashire
User status: Offline
18th Mar 06 at 20:39   View User's Profile U2U Member Reply With Quote
Dont do the bearings tight, they are supposed to have a tiny bit of play in them.
Adam-D
Member
Registered: 11th May 02
Location: Cheshire
User status: Offline
18th Mar 06 at 21:09   View User's Profile U2U Member Reply With Quote
not so when i wobble em its wobling thou
PaulW
Member
Registered: 26th Jan 03
Location: Atherton, Greater Manchester
User status: Offline
18th Mar 06 at 21:43   View User's Profile U2U Member Reply With Quote
wont really be too bad a job sorting them tho eh??

dude can you give me a call regarding tomorrow too, as emma is here so currently clearing it up with her to come yours and play mechanic
Adam-D
Member
Registered: 11th May 02
Location: Cheshire
User status: Offline
18th Mar 06 at 22:25   View User's Profile U2U Member Reply With Quote
nice one, im leaving early to do this job, so will contact you when im done

 
New Topic
New Poll

Corsa Sport » Message Board » General Chat » well, start one job end up finding a few others 23 database queries in 0.0173590 seconds