corsasport.co.uk
  Not logged in [Login - Register]  
You Are Not Registered Or Not Logged In  

Corsa Sport » Message Board » General Chat » Checking continuity


New Topic
New Poll 		  Subscribe | Add to Favourites

You are not logged in and may not post or reply to messages. Please log in or create a new account or mail us about fixing an existing one - register@corsasport.co.uk

There are also many more features available when you are logged in such as private messages, buddy list, location services, post search and more.


Author Checking continuity
Tom J
Organiser: South Wales
Premium Member

Registered: 8th Sep 03
Location: Bridgend
User status: Offline
7th Apr 06 at 23:32   View User's Profile U2U Member Reply With Quote


Trying to check if my earth is dodgy, which setting do i need it on and what numbers do i look for?
i had it on the one which looks like a speaker and it showed 0 and if i connected it to positive and negative to something bare metal it would flash up a number? does that mean its a good earth

Jules
Member
Registered: 26th Nov 04
Location: Ipswich, Suffolk Status: Happy
User status: Offline
7th Apr 06 at 23:34   View User's Profile U2U Member Reply With Quote
Looking at it I reckon it'll be the little speaker looking symbol to the right of the 200ohms (at the bottom) setting.
Should make a beep when it has continuity between the two probes.
Dave A
USER UNDER INVESTIGATION - DO NOT TRADE

Registered: 10th Dec 03
Location: County Durham
User status: Offline
7th Apr 06 at 23:35   View User's Profile U2U Member Reply With Quote
its the diode tester. the bit above where it says: 10ADC. turn the meter onto this and hold the test probes together. should get a 'beep' from the meters.
Tom J
Organiser: South Wales
Premium Member

Registered: 8th Sep 03
Location: Bridgend
User status: Offline
7th Apr 06 at 23:37   View User's Profile U2U Member Reply With Quote
mine hasnt got the little speaker thing, im on about the symbol above the 10ADC.
Tom J
Organiser: South Wales
Premium Member

Registered: 8th Sep 03
Location: Bridgend
User status: Offline
7th Apr 06 at 23:38   View User's Profile U2U Member Reply With Quote
oh and it doesnt beep
Jules
Member
Registered: 26th Nov 04
Location: Ipswich, Suffolk Status: Happy
User status: Offline
7th Apr 06 at 23:38   View User's Profile U2U Member Reply With Quote
Surelky the diode tester will only test for flow one way? i.e it weill beep one way and if you swap the probes around it won't be as it's be 'going against' the diode?
But then again my multimeter is proper old skool with a needle on a meter rather than a digital display - and beeping? That's for nancys!
Tom J
Organiser: South Wales
Premium Member

Registered: 8th Sep 03
Location: Bridgend
User status: Offline
7th Apr 06 at 23:40   View User's Profile U2U Member Reply With Quote
i havent got a clue. i just need to check if my earth is any good, what setting do i need and what number do i look for
Jules
Member
Registered: 26th Nov 04
Location: Ipswich, Suffolk Status: Happy
User status: Offline
7th Apr 06 at 23:42   View User's Profile U2U Member Reply With Quote
As 808 said - the diode tester, and it'll probably read 1.00 but this depends on your multimeter.
Switch it onto that settings and touch the two probes togther and see what it displays on the screen - that will be your answer!

Edit: how are you trying to check your earth? are you checking from chassis to earth or from a 12v supply to earth?

[Edited on 07-04-2006 by Jules]
Dave A
USER UNDER INVESTIGATION - DO NOT TRADE

Registered: 10th Dec 03
Location: County Durham
User status: Offline
7th Apr 06 at 23:43   View User's Profile U2U Member Reply With Quote
the diode tester is what you want to use to test continuity. some meters dont beep, just give a reading. reading should go to 1 if there is continuity and if there is poor continuity will have a figure (usually 3 digits) in the display. For an earth you should get a 0 or 1 as a reading.
Dave A
USER UNDER INVESTIGATION - DO NOT TRADE

Registered: 10th Dec 03
Location: County Durham
User status: Offline
7th Apr 06 at 23:45   View User's Profile U2U Member Reply With Quote
touch the probes together. what reading do you get?

whatever that reading is thats what you need to look for when testing the earth. if the number is higher than the number shown when testing the earth then you have poor continuity.

hope that makes sense

most modern meters do beep tho!
Tom J
Organiser: South Wales
Premium Member

Registered: 8th Sep 03
Location: Bridgend
User status: Offline
7th Apr 06 at 23:46   View User's Profile U2U Member Reply With Quote
i was putting it on a positive cable then onto a point i want to earth my amp too. it was showing 1 constantly and it would flash a random number if i took it off a piece of metal.
Tom J
Organiser: South Wales
Premium Member

Registered: 8th Sep 03
Location: Bridgend
User status: Offline
7th Apr 06 at 23:47   View User's Profile U2U Member Reply With Quote
i get 001 if i touch them together on that setting that looks like a car horn
Tom J
Organiser: South Wales
Premium Member

Registered: 8th Sep 03
Location: Bridgend
User status: Offline
7th Apr 06 at 23:48   View User's Profile U2U Member Reply With Quote
think i've confused you now
Dave A
USER UNDER INVESTIGATION - DO NOT TRADE

Registered: 10th Dec 03
Location: County Durham
User status: Offline
7th Apr 06 at 23:54   View User's Profile U2U Member Reply With Quote
quote:
Originally posted by Tom J
i was putting it on a positive cable then onto a point i want to earth my amp too. it was showing 1 constantly and it would flash a random number if i took it off a piece of metal.


thats not testing continuity! to test for an earthing point put the meters on the bit above 10ADC then put one lead onto a good earth and the other onto the point you wish to earth your amp. check there is good continuity (or connection) by looking for a figure similar to the one you get when touching the probes together.
Dave A
USER UNDER INVESTIGATION - DO NOT TRADE

Registered: 10th Dec 03
Location: County Durham
User status: Offline
7th Apr 06 at 23:56   View User's Profile U2U Member Reply With Quote
or put it onto 20v dc then one onto a 12v positive and the other onto the point you wish to earth the amp. if you get 12v+ then that will be fine.
Tom J
Organiser: South Wales
Premium Member

Registered: 8th Sep 03
Location: Bridgend
User status: Offline
8th Apr 06 at 00:03   View User's Profile U2U Member Reply With Quote
ok cheers bob
Dave A
USER UNDER INVESTIGATION - DO NOT TRADE

Registered: 10th Dec 03
Location: County Durham
User status: Offline
8th Apr 06 at 00:04   View User's Profile U2U Member Reply With Quote
its 808 actually
Tom J
Organiser: South Wales
Premium Member

Registered: 8th Sep 03
Location: Bridgend
User status: Offline
8th Apr 06 at 00:06   View User's Profile U2U Member Reply With Quote
thought it meant corsa BOB
Dave A
USER UNDER INVESTIGATION - DO NOT TRADE

Registered: 10th Dec 03
Location: County Durham
User status: Offline
8th Apr 06 at 00:09   View User's Profile U2U Member Reply With Quote
no you are mistaken. its definately 808.

should i change my name to bob?
John
Member
Registered: 30th Jun 03
User status: Offline
8th Apr 06 at 05:26   View User's Profile U2U Member Reply With Quote
Put it to any one of the settings in bottom left corner.
If you have continuity it'll be a 1.

 
New Topic
New Poll

Corsa Sport » Message Board » General Chat » Checking continuity 23 database queries in 0.0120800 seconds