Robin
Premium Member
Registered: 7th Jan 04
Location: Northants Drives: Clio 182 Cup
User status: Offline
|
It's been proven to be good enough for 190bhp, and I'm sure it would flow enough for a lot more. That doesn't mean you can bolt it on and gain 84bhp though
The spec is -
enlarged and reshaped ports
enlarged throats
3 angle valve seats
cut back valve guides
It has none of the following -
cams
lifters
springs
collets
it has some valves, and others can be supplied if I get the asking price.
So, it's a bare head, but it's ideal for pretty much any X16XE, no matter what your spec is.
On an engine with a mild spec, it showed an 8bhp gain over the same spec without.
One of the combustion chambers has been repaired after it was damaged, but it shouldn't make any difference to the performance of the head.
I will supply some pictures when I can get to the garage (when the rain stops)
SOLD
[Edited on 07-09-2007 by Robin]
|
Robin
Premium Member
Registered: 7th Jan 04
Location: Northants Drives: Clio 182 Cup
User status: Offline
|
TTT
|
Robin
Premium Member
Registered: 7th Jan 04
Location: Northants Drives: Clio 182 Cup
User status: Offline
|
Pictures -
These are the combustion chambers from gearbox end to cambelt, with the last one being the repaired one
The inlet ports in the same order -
Exhaust ports, again, gearbox to cambelt -
Top -
Bottom (freshly skimmed) -
With the 12 valves -
Without -
Cambelt end -
Gearbox end -
The cam area has been trimmed to allow clearance for 288degree Newman cams, but others will fit also -
They're just a couple of the bits which have been done, the others were the same.
Part number -
And a random shot -
The head was chemically cleaned before I had it, it's just corroded slightly on the outside, but with a slight brush, it'll come up like new.
Hope that's enough pics
|
SAL
Premium Member
Registered: 19th Dec 05
Location: Radlett, Hertfordshire
User status: Offline
|
nice, should sell pronto
|
Robin
Premium Member
Registered: 7th Jan 04
Location: Northants Drives: Clio 182 Cup
User status: Offline
|
Price might put some people off Stavs, as you can get your own done by other people for this cash, but this is far better than most of the ones with just a quick buzz with a Dremel.
Hopefully it won't be here long, should fund the coilies for the Golf.
|
Robin
Premium Member
Registered: 7th Jan 04
Location: Northants Drives: Clio 182 Cup
User status: Offline
|
up again
|
Robin
Premium Member
Registered: 7th Jan 04
Location: Northants Drives: Clio 182 Cup
User status: Offline
|
BTTT
|
Scotty C
Member
Registered: 6th Nov 05
Location: Kidderminster Drives: 1.6 16v Sport
User status: Offline
|
bump
|
Robin
Premium Member
Registered: 7th Jan 04
Location: Northants Drives: Clio 182 Cup
User status: Offline
|
Ta Scott
|
Robin
Premium Member
Registered: 7th Jan 04
Location: Northants Drives: Clio 182 Cup
User status: Offline
|
Oh, it will also fit X14XE, X16XEL and C16XE engines.
|
Robin
Premium Member
Registered: 7th Jan 04
Location: Northants Drives: Clio 182 Cup
User status: Offline
|
TTT, offers will be considered, I need the cash.
|
Robin
Premium Member
Registered: 7th Jan 04
Location: Northants Drives: Clio 182 Cup
User status: Offline
|
^
|
Robin
Premium Member
Registered: 7th Jan 04
Location: Northants Drives: Clio 182 Cup
User status: Offline
|
Still for sale.
Need it gone so I can tax/mot my car...
|