Thoday
Member
Registered: 12th Jan 03
Location: Drove kitted corsa b now standard corcs c exclusiv
User status: Offline
|
got a sub box with 2 4002 subs in, has a set of terminals on either side.
i think i need a 4way amp, do i? is 6oow ok?
currently have a 300w amp 2 way tho, runnning my 6by9s
not enought though is it
iv herd runing 2 amps is a strain on the battery
|
Tim
Site Administrator
Registered: 21st Apr 00
User status: Offline
|
Battery is only as strained as the power total you're trying to pull.
Does the box have two sets of terminals? Thats just one for each sub as the box will be partitioned inside into two seperate boxes.
I run two 12's from a Hifonics Zeus Z600. £320 and very very nice. Wire it in 2Ohm mode and your ear drums will bleed.
Oh, and get a powercap (1F) as it really needs the power.
|
Tim
Site Administrator
Registered: 21st Apr 00
User status: Offline
|
Oh, and put a diesel battery in your car. Cheap way to get a battery which can supply more current.
|
SRi_Lad
Member
Registered: 10th Sep 02
User status: Offline
|
you wanna, have a seperate amp running your subs cos otherwise the subs will drain all the power from your amp running the 6x9s.
All you need is a good 2 channel amp!
Your best bet is to post this in the Ice and electrics area, but hope that helps!!
|
Thoday
Member
Registered: 12th Jan 03
Location: Drove kitted corsa b now standard corcs c exclusiv
User status: Offline
|
ice and electrics area is dead, no one responds!
yes there are 2 sets of terminals. i did attempt to buy a 600w 4 way amp, but got sent a 500w 2 way, this wont work will it??? goin to run the 6by9s back off the headunit.
that help?
|
SRi_Lad
Member
Registered: 10th Sep 02
User status: Offline
|
Heres my amp set up, it's a sh1t pick, but had to rush out and take it cos I'm at work!!
Basically the amp on the left is 4 channel which runs the 6x9s and components (once connected)
and the amp on the right is 2 channel which runs the subs.
You can run the 6x9s off of the headunit, wouldn't recommend it though, but at least you will be able to run the subs without straining the 6x9s.
Does that help?
[Edited on 20-02-2003 by SRi_Lad]
|
Thoday
Member
Registered: 12th Jan 03
Location: Drove kitted corsa b now standard corcs c exclusiv
User status: Offline
|
sorta. so with this 500w amp, can i run 2 subs off it, they are in a carpeted baox 2geva. it says 1x 500w or 2x250 wat? not a clue about it tho!
|
Tim
Site Administrator
Registered: 21st Apr 00
User status: Offline
|
Well, if there's two terminals, you just run each sub from each terminal.
Either that, or you run wires from each terminal, twist both +'s and both -'s together, and run the amp bridged into one channel (i.e. i-ve on one channel and +'ve on the other). Check your amp manual though and you may need to flick a switch to put it in bridge mode.
|
SRi_Lad
Member
Registered: 10th Sep 02
User status: Offline
|
Yeah, Tim is right. Basically what 1x 500w, 2x250w means is that you can run 1 channel (bridged) at 500w or 2 channels at 250w.
You'll use a channel for each sub.
It will work.
|
Thoday
Member
Registered: 12th Jan 03
Location: Drove kitted corsa b now standard corcs c exclusiv
User status: Offline
|
ok cheers, thinking im getin it lol.
|
