corsasport.co.uk
  Not logged in [Login - Register]  
You Are Not Registered Or Not Logged In  

Corsa Sport » Message Board » General Chat » X12SZ won`t start after headgasket change (not valve timing)


New Topic
New Poll 		  Subscribe | Add to Favourites

You are not logged in and may not post or reply to messages. Please log in or create a new account or mail us about fixing an existing one - register@corsasport.co.uk

There are also many more features available when you are logged in such as private messages, buddy list, location services, post search and more.


Author X12SZ won`t start after headgasket change (not valve timing)
Chitrenegade
Member
Registered: 13th Sep 17
User status: Offline
13th Sep 17 at 18:03   View User's Profile U2U Member Reply With Quote
Hi Guys from an ole Yank living in Berlin...Trying to do a friend a favor and changed his head gasket on an 1997 1.2L Corsa, which went really smooth. Jumped in and turned the engine over only to find that I didn`t have a fuel pump or Ignition. Checked wiring and jumped FP fuse and pump works fine. I believe that the ECU is maybe not getting the chip code. The ECU has constant Battery power to 2 pins (A16 and B1-maybe, my poor memory) anyway, where is the Ignition switched power to the ECU? Is there any way to troubleshoot the transponder or ECU? I have been dogged before, but have always managed to win the battle, but this has got me stumped. Any Ideas from the specialist is greatly appreciated and plenty of Good Ole German Beer if we win this battle........Dankeschoene....Chit
Chitrenegade
Member
Registered: 13th Sep 17
User status: Offline
13th Sep 17 at 18:21   View User's Profile U2U Member Reply With Quote
That was pin C16 & B1 with constant voltage, someone told me these pins are Bat volts and pin A6 should be Ignition switched power....well, I don`t have a wire at terminal A6....My buddy drove the car to me on 3 cylinders without any ECU problems. Under the bonnet, no bent pins on wiring plugs, no crushed wiring inside wiring harness, I opened up the wiring harness to check. I checked half the wiring for continuity and they were fine. I need to get another view and different thought on what this might be........Thanks, and <KEEP THE RUBBER SIDE - DOWN>
Chitrenegade
Member
Registered: 13th Sep 17
User status: Offline
13th Sep 17 at 19:57   View User's Profile U2U Member Reply With Quote
corsa has obdII plug but it has never given codes, I Believe it is before the system went into production. WHO SAID...Point Ignition and Carburators are nothing but Trouble?
Chitrenegade
Member
Registered: 13th Sep 17
User status: Offline
13th Sep 17 at 22:02   View User's Profile U2U Member Reply With Quote
How does a car.thief get around the key transponder? A 20 year old car can't provide security unbreakable in today's world. Does the transponder send a sine wave or just a voltage that anyone could simulate?
Tiger
Member
Registered: 12th Jun 01
Location: Leicestershire Drives:Astra VXR
User status: Offline
13th Sep 17 at 22:06   View User's Profile U2U Member Reply With Quote
My 2000 vw van has obdII but it can't be used for diagnostics.
Chitrenegade
Member
Registered: 13th Sep 17
User status: Offline
13th Sep 17 at 22:16   View User's Profile U2U Member Reply With Quote
I wonder when Europe made it into law, DOT Started in 96 & required the 98 models to have it.
J100RSA
Member
Registered: 4th Mar 01
Location: Thornhill, West Yorkshire
User status: Offline
13th Sep 17 at 22:20   View User's Profile U2U Member Reply With Quote
have you had the crank pulley off? is the orange engine management light flashing?
Chitrenegade
Member
Registered: 13th Sep 17
User status: Offline
13th Sep 17 at 22:29   View User's Profile U2U Member Reply With Quote
Good points, but the crank pulley was not removed and the MEL does not come on at all. While checking for ignition power at the ECU I found one wire that turned on the MEL. The light went on but still no fuel pump or ignition.
Chitrenegade
Member
Registered: 13th Sep 17
User status: Offline
13th Sep 17 at 22:30   View User's Profile U2U Member Reply With Quote
EML...TABLET WRITES MEL
Chitrenegade
Member
Registered: 13th Sep 17
User status: Offline
13th Sep 17 at 22:39   View User's Profile U2U Member Reply With Quote
I will return in the Morning...good night...Chit
Ian
Site Administrator

Avatar

Registered: 28th Aug 99
Location: Liverpool
User status: Offline
13th Sep 17 at 22:50   View Garage View User's Profile U2U Member Reply With Quote
This sounds very much like a cam/crank signal issue which is causing the ECU to inhibit fuel and spark.

Immobiliser is somewhere to look but you've not really disturbed that whereas timing is more closely connected to that job.
Ste
Premium Member

Avatar

Registered: 5th Mar 03
Location: Taif, Saudi Arabia
User status: Offline
14th Sep 17 at 05:04   View Garage View User's Profile U2U Member Reply With Quote
Your fault will more than likely lie where you have disturbed something rather than a new fault appearing magically.
Go back and check everything you have disturbed.

I would rather lose by a mile because i built my own car, than win by an inch because someone else built it for me.
Chitrenegade
Member
Registered: 13th Sep 17
User status: Offline
14th Sep 17 at 08:56   View User's Profile U2U Member Reply With Quote
Ian, there is no cam sensor but a 3 wire crank sensor, and could be a problem, but I Thought the fuel pump primes, then waits for a signal that the engine turn or runs. Is there a test for the crank sensor?
Chitrenegade
Member
Registered: 13th Sep 17
User status: Offline
14th Sep 17 at 09:03   View User's Profile U2U Member Reply With Quote
Ste, I only got into the wiring because I could not find any other fault. Removing the head I had the wiring harness off the engine and tucked around the hood hinge and thought I might have broken a wire there, not likely but possible.
Chitrenegade
Member
Registered: 13th Sep 17
User status: Offline
14th Sep 17 at 10:40   View User's Profile U2U Member Reply With Quote
My buddy blames the battery being disconnected for 2 days as the culprit. I have never had any problem with that except reprogramming door locks, newer cars with electronic gas pedal & etc....from now on, jumper cables to a motorcycle battery!!!
Chitrenegade
Member
Registered: 13th Sep 17
User status: Offline
14th Sep 17 at 10:42   View User's Profile U2U Member Reply With Quote
I have cleaned all the ground points that I found also.
Chitrenegade
Member
Registered: 13th Sep 17
User status: Offline
14th Sep 17 at 17:56   View User's Profile U2U Member Reply With Quote
Is there anyway to bypass the key transponder?? What type of signal is sent to ECU? Any test for the transponder? THERE IS NO SPARK & NO PWR TO THE FUEL PUMP. THOUGHT...I need to check if I have pwr to the coil...
J100RSA
Member
Registered: 4th Mar 01
Location: Thornhill, West Yorkshire
User status: Offline
14th Sep 17 at 23:23   View User's Profile U2U Member Reply With Quote
you have refitted the brown earth wires on the on carrier haven't you?
Chitrenegade
Member
Registered: 13th Sep 17
User status: Offline
16th Sep 17 at 00:31   View User's Profile U2U Member Reply With Quote
THANKS J100RSA, But I removed all the grounds I could find & cleaned them too...but no help. I thought since I HAVE NO IGNITION & no fuel pump,,, maybe by a long chance the ignition switch is not connecting in position 2! Although it turns the starter in position 3! Out of town now, but will check it first thing Monday. & I welcome any comments. THANKS
Ian
Site Administrator

Avatar

Registered: 28th Aug 99
Location: Liverpool
User status: Offline
16th Sep 17 at 02:10   View Garage View User's Profile U2U Member Reply With Quote
quote:
Originally posted by Chitrenegade
I Thought the fuel pump primes, then waits for a signal that the engine turn or runs.


No - if the crank sensor is open circuit it'll inhibit fuel and spark
Chitrenegade
Member
Registered: 13th Sep 17
User status: Offline
16th Sep 17 at 08:32   View User's Profile U2U Member Reply With Quote
FANTASTIC, I Only assumed that it would Prime without any signal from the crank sensor, now I have 3 areas to trouble shoot. Glad to leave behind the immobilizer idea. I know the wire plug was clean & all 3 pins not damagedo the crank sensor. Will have to connect oscilloscope to check it. THANKS IAN, Will keep you posted on Tuesday.
J100RSA
Member
Registered: 4th Mar 01
Location: Thornhill, West Yorkshire
User status: Offline
17th Sep 17 at 13:11   View User's Profile U2U Member Reply With Quote
if the crank sensor was open circuit you would still get eml it sound more like you lost a switched live to ecu. I assume you have checked fuses??
Chitrenegade
Member
Registered: 13th Sep 17
User status: Offline
17th Sep 17 at 17:55   View User's Profile U2U Member Reply With Quote
Mr. J100RSA, with my respect, you are 100% right, I have NO live switched power to the ecu. 2 Battery live terminals, but no switched and no eml light. Just returned home and will continue tomorrow with all the new ideas. By the way, I have read a lot of your older post and you are most often definitely right on the Nail Head. Thanks, and will keep you'll posted.

 
New Topic
New Poll

Corsa Sport » Message Board » General Chat » X12SZ won`t start after headgasket change (not valve timing) 24 database queries in 0.0150621 seconds