david clay
Member
Registered: 12th Aug 11
User status: Offline
|
any1 no how to fit hids
|
Matty W
Member
Registered: 31st Jan 11
Location: Ashton-in-Makerfield, Greater Manchester
User status: Offline
|
Should be instructions in the box, general idea is wire the ballast unit up to your original headlamp wiring following the instructions, make sure you mount all the ballast and control units securely and somwhere they arent going to get sprayed when it rains , ive seen them covered with plastic bags before although im not sure how safe it is. dont forget to check your headlamp level against a brick wall before and after, just to compare and see if you need to make any ajustments, nothing worse than being dazzled by hid's
|
SeanXE
Member
Registered: 17th Jan 09
Location: Luton
User status: Offline
|
Coming along nicely
|
david clay
Member
Registered: 12th Aug 11
User status: Offline
|
well not much really done today due to weather fitted my hid kit and gaitor set will upload pics tomoz still to do paint calipers and drums also ordered some standard mirrors
|
david clay
Member
Registered: 12th Aug 11
User status: Offline
|
well ordered some standard mirros so the m3 ones will be for sale
|
david clay
Member
Registered: 12th Aug 11
User status: Offline
|
well all front ends done back drums are done all steelies are painted black will upload pics of the steelies tomoz
|
david clay
Member
Registered: 12th Aug 11
User status: Offline
|
just to do the back drums and fit the wheels then wash the car will upload pics tomoz
|
david clay
Member
Registered: 12th Aug 11
User status: Offline
|
|
david clay
Member
Registered: 12th Aug 11
User status: Offline
|
well bad times i was finishing off the bakc passenger drum tonight went inside to get the paint and come bakc out and some fuckers had pushd my car off the axle stand lukily it had 3 wheels on the axle stand went through th sill made a little hole but can be fixed so gonna get it repaird asap
|
david clay
Member
Registered: 12th Aug 11
User status: Offline
|
well done back and front so gonna wash the car tomorrow then fit my mirrors when they arrive its booked in at the body shop to be reapaired tomorrow
|
david clay
Member
Registered: 12th Aug 11
User status: Offline
|
|
david clay
Member
Registered: 12th Aug 11
User status: Offline
|
|
david clay
Member
Registered: 12th Aug 11
User status: Offline
|
plans next find out what the nocking noise is on the passenger side get the sill repaird tommorrow and wash and polish it and vac inside out
|
SeanXE
Member
Registered: 17th Jan 09
Location: Luton
User status: Offline
|
what sort of noise?
|
david clay
Member
Registered: 12th Aug 11
User status: Offline
|
when the passenger wheel goes over a speedbump or any sort of uneven road
nocking noise banging noise loose noise lol all i no is that it is loud
|
DansCorsaSXi
Organiser: Yorkshire Premium Member
Registered: 13th Jan 10
Location: Worksop
User status: Offline
|
Top of suspension tightened up properly?
Star silver C20XE SXi Project thread
Smoke Grey Corsa GSi Project thread
|
DanCobb
Member
Registered: 14th May 11
Location: Lewes/Brighton
User status: Offline
|
What spring are on it? Could be the spring not sitting correctly. Happened on mine a few months ago sounded like the wheel was gunna fall off just twisted it around problem solved
|
DanCobb
Member
Registered: 14th May 11
Location: Lewes/Brighton
User status: Offline
|
Springs*
|
david clay
Member
Registered: 12th Aug 11
User status: Offline
|
well not muc of an update recieved my standard mirrors today so fitted them washed and polishd the car and cleaned inside re routed all my sub and amp wiring looks alot neater
|
david clay
Member
Registered: 12th Aug 11
User status: Offline
|
|
david clay
Member
Registered: 12th Aug 11
User status: Offline
|
|
david clay
Member
Registered: 12th Aug 11
User status: Offline
|
next on list get the sill repaird and fit my gm mudflaps then go from there
|
kie1995
Member
Registered: 18th Oct 11
Location: Leicestershire
User status: Offline
|
looking good pal...love that exhaust!!
|
david clay
Member
Registered: 12th Aug 11
User status: Offline
|
cheers pal its getting there slowly it would be faster project but money income lol and its just a stainless steel one cost me £20
not too loud just right
|
kie1995
Member
Registered: 18th Oct 11
Location: Leicestershire
User status: Offline
|
quote: Originally posted by david clay
cheers pal its getting there slowly it would be faster project but money income lol and its just a stainless steel one cost me £20
not too loud just right
same with my project lol i'm skint...n really like the twin exhaust's!!
|