Matt L
Member
Registered: 17th Apr 06
User status: Offline
|
1) iv just swapped the bulbs in the mfd and one of the screws that holds it down fell down into the fan part. iv tried my fans on all the settings and cant hear anythin. will this be ok or will i need to get it out???
2) also my hazzard lights switch is being gay if it turns on and then i press it it wont go off and then if its off and i press it it wont go on so i have to take the switch off and press it that way to get it to work.
any help with either of these problems would be greatly appreciated.
cheers matt
edited because it made no sense
[Edited on 09-09-2006 by Matt L]
|
vx.racing
Member
Registered: 17th Feb 06
Location: Tyrone, Northern Ireland
User status: Offline
|
If you have taken the hazard lights plug out and put it back in then you may have put it in upside down, which will cause it to stick when you try switching it.
|
Matt L
Member
Registered: 17th Apr 06
User status: Offline
|
ah right cool ill try takin it out and turnin it round cheers.
edit even though i dont think i took it out but its worth a try.
[Edited on 09-09-2006 by Matt L]
|
SHARPY
Member
Registered: 11th Nov 04
Location: Wigan, Lancs Drove: x14xe Sport
User status: Offline
|
if you removed the heater control panel it wont be fitted back properly as my hazard switch did that when i replaced the heater bulbs ... worth a try if you've had it to bits that is
|
Planty02
Member
Registered: 5th Mar 05
Location: Burslem, Stoke-on-Trent
User status: Offline
|
I had the same problem with my hazards when i sprayed my centre panel. I know this is a bit vague but bear with cos it was a while ago but mine did it because i forgot to put 2 screws back in that held the front facia to the white plastic behind...have a look to make sure thyre in - should be brassy coloured ones - This will only have happened if you have taken the centre panel off, if you have then take it out again and check for the missing screws holding the front panel to the white plastic behind
[Edited on 09-09-2006 by Planty02]
[Edited on 10-09-2006 by Planty02]
|
Planty02
Member
Registered: 5th Mar 05
Location: Burslem, Stoke-on-Trent
User status: Offline
|
...Also the screw should be fine as long as its not catching in the fans or anything (sounds like its not)
|
Matt L
Member
Registered: 17th Apr 06
User status: Offline
|
well the screw isnt amking any noises so i think thats fine. as for the hazard lights i havent tried anything yet. all i did was take the vent things out anf stick them back in once id changed the bulbs.
|
Matt L
Member
Registered: 17th Apr 06
User status: Offline
|
and i never did replace the screw. so its missin a screw that holds the mffd down
|
SHARPY
Member
Registered: 11th Nov 04
Location: Wigan, Lancs Drove: x14xe Sport
User status: Offline
|
make sure the clips that hold the heater panel on are clipped on aswell, when i did mine and the hazard switch wouldent turn off i found the panel wasnt clipped on properly
|
Planty02
Member
Registered: 5th Mar 05
Location: Burslem, Stoke-on-Trent
User status: Offline
|
Try replacing the screw before trying anything else - maybe pinch a screw out of one of the side pockets or somewhere
|
Matt L
Member
Registered: 17th Apr 06
User status: Offline
|
i think ill check it out on wednesday.
|
Matt L
Member
Registered: 17th Apr 06
User status: Offline
|
put the screw in and its still the same but i think i know whats wrong with it; i just dont know how to sort it out. how to explain. rite if you take the switch off theres supposed to be a very small gap around the thing that you puch in and i think that when iv taken the vents out iv pushed them in so the switch wont go down far enough.
i hope that makes a bit of sense.
any ideas on what to do.
cheers matt
|
