LukeGSi
Member
Registered: 9th Dec 03
User status: Offline
|
I wana fit some tasty leather buckets.........how hard is it to remove the standard front seats?? Another slight prob is i think ive got the wrong subframes....is this a major prob or can they be slightly ''modified''???
|
mike16v
Member
Registered: 20th May 02
Location: sheffield, yorkshire
User status: Offline
|
pretty easy job mate, 1st time i changed mine took less than 2 hours. for seats out, new in, wiht harnesses etc. what sub-frames have u got??
|
Adam-D
Member
Registered: 11th May 02
Location: Cheshire
User status: Offline
|
id get the proper subframes
|
LukeGSi
Member
Registered: 9th Dec 03
User status: Offline
|
Not exactly sure what sub frames they are dammit, but cant really complain as leather cobras and harness' only cost me 80 notes second hand but they're mint!! Will give it a whirl with the sub frames ive got if not i guess ill have to get the proper 1's!! What about harness'......look a bit of a pain in the arse to me????
|
Adam-D
Member
Registered: 11th May 02
Location: Cheshire
User status: Offline
|
harness piss easy
|
mike16v
Member
Registered: 20th May 02
Location: sheffield, yorkshire
User status: Offline
|
3, 4 or 6 point harnesses??
|
LukeGSi
Member
Registered: 9th Dec 03
User status: Offline
|
3 point sparco 1's!!! Think there should be an info post for fitting buckets and harness'!!!
|
mike16v
Member
Registered: 20th May 02
Location: sheffield, yorkshire
User status: Offline
|
harnesses in pic above are 3 point, 2 bolts go where origional seat belt tensioner go (1 either side of seat) and the other goes in a hole for the rear seat belt, when u come to fit them u will see, its dead simple mate
|
Adam-D
Member
Registered: 11th May 02
Location: Cheshire
User status: Offline
|
right removal
slide seats forward and tilt
undo the plastic trim in the centre bit "torx screws" unclip and remove
put the pretansior fork into the hole to make it safe instructions are on it to tell you aswell
undo the two torx bolts at the back of the seatrol seat and frame forward slide forward a bit and lift out.
pull off the rear door cards undo the old seat belt and the top mount then the bottom bar bolt rotate and twist the bar and pull it out "wiglle it bit tricky"
then put new subfram in slot it in and bolt it down
slit its runners forward put new seat on and bolt halfway on slide seat back and locate the back bolts in then tigten up diagonly.
harnesses
feed the bottom bits throu the holes top back of the seat then side holes bolt centre back the where you can see on the pics "rear seatbelt mount" the the left hand side to the sub frame and right hand side to the seatbelt bar bolt that is now removed revese sides for passenger side so left hand side to bottom belt bar hole and right to sub frame
dead easy
|
LukeGSi
Member
Registered: 9th Dec 03
User status: Offline
|
Coolio.......cheers guys!! Gona attempt it 2moro 
|
mike16v
Member
Registered: 20th May 02
Location: sheffield, yorkshire
User status: Offline
|
let us know how u go on m8ty
|
LukeGSi
Member
Registered: 9th Dec 03
User status: Offline
|
Will do, then comes getting rid of the rear seats and doing some kinda of mdf build!!! Sorting out premium member thingy 2moro so ill post heapz of pics when i fix my camera!! 
|
