ChazSXi
Member
Registered: 26th Jan 03
Location: Waterlooville, Hampshire
User status: Offline
|
 #
how do i fit it?
|
corsa-sxi
Member
Registered: 11th Jul 03
Location: Kingston upon Hull
User status: Offline
|
remove the air box
undo the cold air feed, then loosen the nut of the clip from the hose going from the airbox to the engine....
remove lid of the air box and to removed the whole thing u pull towards u and lift it up...
to fit the ind kit,
place the rubber ring inside the neck on the ind kit and place the clip that came with the ind kit around the neck of the cone, now slide the cone over the hose going to the engine....
secure the cone by inserting the long black screw thingy, into one of the holes from the airbox mounting holes and tighten the nut to secure..
[Edited on 17-05-2004 by corsa-sxi]
|
HeNdie
Member
Registered: 8th May 04
Location: Wigan. Drives:Saxo VTR!
User status: Offline
|
how much would a garage charge?
|
Rob B
Member
Registered: 8th Jan 04
Location: Area Motorsport Drives: Race EP3
User status: Offline
|
lmao a garage to fit an induction kit
|
IntaCepta
Member
Registered: 25th Mar 02
Location: Mill Hill East, Greater London
User status: Offline
|
lol, just think of it like lego,
take 2 blocks apart and replace one block with another.
its a 10min job tops!
open ur bonnet, it will all make sense mate.
|
Adam-D
Member
Registered: 11th May 02
Location: Cheshire
User status: Offline
|
itlll suck in hot air when you pull upto junctions and lose you power
|
ChazSXi
Member
Registered: 26th Jan 03
Location: Waterlooville, Hampshire
User status: Offline
|
quote:
Originally posted by Adam-D
itlll suck in hot air when you pull upto junctions and lose you power
can i get a metal sheet and becn it round to stop it doing this? like a heatshield?!
|
Siberia
Member
Registered: 9th Oct 03
Location: Leprechaun Land Drives : Zafira GSI
User status: Offline
|
quote:
Originally posted by IntaCepta
lol, just think of it like lego,
take 2 blocks apart and replace one block with another.
thats one way of putting it 
|
Adam-D
Member
Registered: 11th May 02
Location: Cheshire
User status: Offline
|
ypu could make one but a panel performance filter works better really
|
Siberia
Member
Registered: 9th Oct 03
Location: Leprechaun Land Drives : Zafira GSI
User status: Offline
|
quote:
Originally posted by ChazSXi
quote:
Originally posted by Adam-D
itlll suck in hot air when you pull upto junctions and lose you power
can i get a metal sheet and becn it round to stop it doing this? like a heatshield?!
u can but why would ya go to the hassle??
get a k& n pannel filter and drill you airbox. It will make all the noise u want if u drill it right and it wont suck in hot air.
|
Wolf In Welsh Clothing
Member
Registered: 31st Mar 03
Location: North Wales...... Cooper S on order
User status: Offline
|
1. Remove standard airbox.
2. Take one of the round rubbers off the air box (to go in the hole closest to the inlet pipe) if it is still on the airbox.
3. Put jubilee clip with clamp on to air filter followed by other clip.
4. Bolt clamp in to airbox rubber hole.
5. Put inlet pipe onto filter and jubilee clip on to pipe.
6. Tighten Jubilee clips.
7. Find a garage that wont rip you off should you want anything else fitting to your car.
|
Fraser Young
Member
Registered: 26th Dec 02
Location: Dundee City Drives: 58 Impreza WRX
User status: Offline
|
quote:
Originally posted by HeNdie
how much would a garage charge?
15 quid and a good laugh at your expense...
|
corsa-sxi
Member
Registered: 11th Jul 03
Location: Kingston upon Hull
User status: Offline
|
how do u drill an airbox right?
|
Siberia
Member
Registered: 9th Oct 03
Location: Leprechaun Land Drives : Zafira GSI
User status: Offline
|
quote:
Originally posted by corsa-sxi
how do u drill an airbox right?
with the right size drill bit and enough holes
u'd be surprised there was one dude on here that was wondering y his drilled airbox didnt make any louder noise.
turned out he had drilled the top of the box
|
Wolf In Welsh Clothing
Member
Registered: 31st Mar 03
Location: North Wales...... Cooper S on order
User status: Offline
|
I know a lad that did that too!
Showed me it and burst out laughing!!!!!
Chucked my inductin kit on for him to try then he got a pipercross 2nd hand.
As for drilling an airbox, loads of holes in any areas away from engine in the BOTTOM of the box, AND MAKE SURE YOU REMOVE THE PIPE IN THE TOP OF THE BOX.
|
