ed
Member
Registered: 10th Sep 03
User status: Offline
|
If the bolts holding the ehxhaust manifold are so rusted they dont have any shape to them and I can't get a socket to fit onto it, how the hell do I get them undone? Tried mole grips and pipe pliers... No luck
And the other thing... How do I drain the gearbox oil from a C20XE?
Tahnx
|
langey
Member
Registered: 7th Sep 03
Location: Wigan
User status: Offline
|
1st thing, spary WD-40 on them and rub them down with some sorta sand paper, job done, socket fits on.
2nd thing, i dunno
|
Ian
Site Administrator
Registered: 28th Aug 99
Location: Liverpool
User status: Offline
|
If they don't have shape because they're rusty, remove the rust. If they don't have any because you've chewed them, you're a little more stuck.
Mole grips should do it tbh.
|
BeArDy
Member
Registered: 7th Aug 00
Location: Manchester
User status: Offline
|
stud extractor (spelling) there a life saver
|
langey
Member
Registered: 7th Sep 03
Location: Wigan
User status: Offline
|
you need to tighten the molegrips more
or just MAKE the socket fit, especially if they aint yours
|
Kris TD
Member
Registered: 25th Mar 02
Location: Ware, Hertfordshire
User status: Offline
|
angel grinder and then buy some new ones
|
broster
Premium Member
Registered: 6th Dec 02
Location: Drives: E39
User status: Offline
|
quote: Originally posted by langey
or just MAKE the socket fit, especially if they aint yours
hahaha love it! not lending you my tools
[Edited on 18-06-2004 by broster]
|
ed
Member
Registered: 10th Sep 03
User status: Offline
|
I sprayed them all a few days ago with WD40 to get the oil to penitrate, and did some more today... This meant I got most of them out, but there were 3 that I put the socket on, and it just spun, either the person who had the car before me has chewwed them, or they have fallen appart - think its the latter due to the ammount of rust on that car...
|
ed
Member
Registered: 10th Sep 03
User status: Offline
|
quote: Originally posted by Kris TD
angel grinder and then buy some new ones
Can't get my angle grinder to fit in the gap to grind off the bottom ones...
|
langey
Member
Registered: 7th Sep 03
Location: Wigan
User status: Offline
|
quote: Originally posted by broster
quote: Originally posted by langey
or just MAKE the socket fit, especially if they aint yours
hahaha love it! not lending you my tools
|
Mattb
Member
Registered: 2nd Feb 03
Location: Under your sisters bed
User status: Offline
|
gearbox oil.. have two options..
remove driveshaft, place g/box on its side.
or
undo the diff plate and drain it that way
|
ed
Member
Registered: 10th Sep 03
User status: Offline
|
the diff plate is a bit stuck on, and that car scares the living shit out of me (I dont want to spend too much time under it). It is a death trap, you and Steve are lucky to be alive after driving it back.... The floorpan is completely rotten... The brake pads are fucked, I pulled the disk off and all the material fell of it....
If I set my engine crane to a higher weight, you reckon it will be ok to lift it out with the oil still in it?
|
Mattb
Member
Registered: 2nd Feb 03
Location: Under your sisters bed
User status: Offline
|
yeh.....
just give me a shout if you get stuck, you got my number
|