adam 1.4 sport
Member
Registered: 2nd Jun 08
Location: luton
User status: Offline
|
what bar should i be running a c20let running 1bar off boost ? as some say 3.5 and some have said 4.5?
And when ajusting the fuel pressure do you ajust it with the vacuum pipe on or off ?
|
Jamie_Hastings1
Member
Registered: 14th Aug 08
Location: Sanquhar, Dumfries and Galloway
User status: Offline
|
Its not to do totally with boost. Get a wideband and set it up properly.
|
Nic Barnes
Member
Registered: 5th Apr 04
Location: nowhere near ginger people
User status: Offline
|
how is it not to do with boost? the fpr works off inlet pressure
|
adam 1.4 sport
Member
Registered: 2nd Jun 08
Location: luton
User status: Offline
|
i will get it set up propally in a month just wat it running right ? 3.5 or 4.5 ?
|
Jamie_Hastings1
Member
Registered: 14th Aug 08
Location: Sanquhar, Dumfries and Galloway
User status: Offline
|
quote:
Originally posted by Nic Barnes
how is it not to do with boost? the fpr works off inlet pressure
Theres more to it than boost though,injectors etc will determine fuel pressure. All c20lets running 14psi boost dont require 3.5 bar fuel pressure.
[Edited on 01-10-2009 by Jamie_Hastings1]
|
Nic Barnes
Member
Registered: 5th Apr 04
Location: nowhere near ginger people
User status: Offline
|
oh right
|
adam 1.4 sport
Member
Registered: 2nd Jun 08
Location: luton
User status: Offline
|
what do you guys recoment then ?
And do you ajust the fpr with the vacuum pipe on or off as they give different readings
|
Jamie_Hastings1
Member
Registered: 14th Aug 08
Location: Sanquhar, Dumfries and Galloway
User status: Offline
|
Is it a chip your using?
|
Jamie_Hastings1
Member
Registered: 14th Aug 08
Location: Sanquhar, Dumfries and Galloway
User status: Offline
|
3.5 Bar with vacum off,i think.
|
adam 1.4 sport
Member
Registered: 2nd Jun 08
Location: luton
User status: Offline
|
its ment ti have a phase 2 chip as got rolling road tested at 287 bout 4 months ago but then my amal valve went and loads off people was fidling round sating it was the fpr so put a mbc onyesterday as it boosts back upto1 bar as it should but need to knw fuel pressure!
|
Jamie_Hastings1
Member
Registered: 14th Aug 08
Location: Sanquhar, Dumfries and Galloway
User status: Offline
|
Didn't know phase 2 to went as much as 287bhp.
|
Nic Barnes
Member
Registered: 5th Apr 04
Location: nowhere near ginger people
User status: Offline
|
seen p2 run over 300 quite a few times tbh
|
Jamie_Hastings1
Member
Registered: 14th Aug 08
Location: Sanquhar, Dumfries and Galloway
User status: Offline
|
I thought phase 2 was good for 280bhp. Can you remap a EDS chip?
|
adam 1.4 sport
Member
Registered: 2nd Jun 08
Location: luton
User status: Offline
|
not sure was boosting fine 100 per cent then the amal valve went and loads off people said it was fuel pressure so they was ajusting away so and it wouldnt boost all all only 0.5bar.... so i fitted a manual boost controler yesterday and it boosts too 1bar as usal but not sure about fuel pressure and the actuator setting as some people say 2-3mm :S
|
adam 1.4 sport
Member
Registered: 2nd Jun 08
Location: luton
User status: Offline
|
??
|
