fred7
Member
Registered: 17th May 04
Location: Rugeley, Staffordshire
User status: Offline
|
Just brought a corsa sport and it has a toad alarm on it but only has 1 key fob, ive brought another one but cant seem to find anything on how to reprogram the new key fob. dont seem to have a code or anything in the paper work for the alram either? its got an immob and dead lock when u start the car aswell so bit stuffed if the battery goes!!! thanks
|
fred7
Member
Registered: 17th May 04
Location: Rugeley, Staffordshire
User status: Offline
|
anyone?
|
chloe16v
Member
Registered: 29th Nov 07
Location: Rotherham
User status: Offline
|
dont know if any of this will help???
Trouble Shooting -
FAULT POSSIBLE REMEDIES
UNIT FAILS TO ARM BY THE RADIO
KEY
If LED not lit - check fuses and power connections.
If LED lit check batteries in all Radio-keyss and that they are
programmed into the unit.
Remember that, other than by Radio-key or active rearm the
alarm will only arm if passive arming is selected.
SIREN DOES NOT OPERATE WHEN
ALARM ACTIVATED
Test by unplugging when armed – the siren will sound. Allow a few
minutes for the siren battery to charge
UNIT WILL NOT ARM OR DISARM BY
RADIO-KEY
Check current Radio-key operation with spare valid radio-key Check
aerial positioning - the higher it is the better reception should be
FALSE TRIGGERING OF ALARM Check sensor sensitivity and that switch operation is reliable
INTERMITTENT FAULT Check all hard wired and plug-in connections
Check for low vehicle battery voltage
IF ALL ELSE FAILS... Contact the Technical Help Desk on 0870 1604433.
Technical
|
chloe16v
Member
Registered: 29th Nov 07
Location: Rotherham
User status: Offline
|
Programming the Alarm Unit
Programming the Customer PIN Code –
The customer PIN code is a 4-digit number used to dis-arm the alarm system in an emergency, and also to
access programming mode. The factory default PIN setting is random, but each of the 4 digits can be set to
any number requested by the customer. The customer should carefully record this PIN. If this PIN is lost,
then essential functions within the alarm will become inaccessible. This PIN code can only be reset by
returning the unit to TOAD. Ensure that the customer is fully aware of the importance of this PIN code.
To enter a 4 digit pin code; for example 4030:
Turn the Ignition within 7 seconds, leaving it “on”.
The LED will now flash Red quickly for 3 seconds, then slows to 1 flash per second.
Count the slow Red flashes until the 4th occurs - turn the ignition “off” immediately after the
LED extinguishes.
Turn the ignition “on” - The LED illuminates Green, then slowly flashes Red.
Before the 1st slow Red flash - turn the ignition “off”.
Turn the ignition “on” - The LED illuminates Green, then slowly flashes Red.
Count the slow Red flashes until the 3rd occurs - turn the ignition “off” immediately after the
LED extinguishes.
Turn the ignition “on” - The LED illuminates Green, then slowly flashes Red.
Before the 1st slow Red flash - turn the ignition “off”.
Note:
As shown above, a 0-digit is entered by turning the ignition “off” immediately after the LED has finished
flashing Red quickly for 3 seconds (if it 0 is the 1st digit of the PIN), or immediately after the LED has
illuminated Green (if it is the 2nd, 3rd or 4th digit of the PIN). i.e. before the 1st slow Red flash occurs.
All other digits are entered by turning the ignition “off” immediately after the LED has extinguished on the
corresponding flash number.
If the PIN code is entered correctly, the system will return to the disarm state when the ignition is switched off.
If the code is entered incorrectly then the system will stay armed and indicate a wrongly entered code by
beeping the siren 5 times.
If an incorrect PIN code is entered 3 times in succession, the alarm will block any further PIN code
attempts for 3 minutes. The PIN code block is shown by the LED giving a double flash in place of the
single flash.
IF THE OPTIONAL TOUCH KEY IS FITTED TO THE ALARM SYSTEM, THIS WILL STILL DISARM THE
ALARM SYSTEM.
Software Switch Sequence –
The alarm unit is supplied with standard default settings and features. To adjust the settings and to adjust
ultrasonic sensitivity, follow the procedure as illustrated in the example below.
To change the Siren Chirp setting (switch 1-5) from On to Off, complete the PIN code entry sequence then:
Turn the
ignition
“on”
You are
now in
switch 1-5
Press button 1, 5 times the
siren will chirp each time
the button is pressed
Press remote
button 1 once
The siren will
chirp as
confirmation
Turn the
ignition “off”
and “on"
Press button 1 once the Led will
turn RED to show any switches
starting with the digit 1
Turn the
ignition “off”
and “on”
Press both buttons on the remote
to toggle the switch from
Off to On or On to Off.
After adjustment, switch the ignition “off” and wait for the system to
exit programme mode indicated by a double chirp of the siren or turn
the ignition back “on” to adjust any other switches.
Technical Support 0870-160 4433 Page 10 Revision
|
chloe16v
Member
Registered: 29th Nov 07
Location: Rotherham
User status: Offline
|
link btw might be easyer 
http://www.eserviceinfo.com/downloadsm/17912/Toad_Ai606.html
|
fred7
Member
Registered: 17th May 04
Location: Rugeley, Staffordshire
User status: Offline
|
haha thanks for that, will have a read thru and see if its but think it will help, just need to find the pin code. thanks anyway
|
