silvertornado
Member
Registered: 9th Oct 09
Location: nottingham NG5 (east mids)
User status: Offline
|
after a 2 minute start up and drive around the block manifold is glowing but its lost power and is losing vacum
car has eml on due to egr being blanked
thanks mark
[Edited on 26-02-2010 by silvertornado]
|
Root
Member
Registered: 28th Dec 08
User status: Offline
|
maybe think about unblanking? see what it does.
|
silvertornado
Member
Registered: 9th Oct 09
Location: nottingham NG5 (east mids)
User status: Offline
|
has been blocked for nearly 2 months and only just started getting this problem in last 2 days
|
SportBoy
Member
Registered: 5th Oct 01
Location: Retford, Nottinghamshire
User status: Offline
|
missfire? timing jumped?
[Edited on 26-02-2010 by SportBoy]
|
silvertornado
Member
Registered: 9th Oct 09
Location: nottingham NG5 (east mids)
User status: Offline
|
timing all spot on but there is a bit of a misfire tbh
|
SportBoy
Member
Registered: 5th Oct 01
Location: Retford, Nottinghamshire
User status: Offline
|
thats prob what is makeing the manifold glow . unburnt fuel will fvck the cat up if you leave it long enough, sort the missfire and all should be good
|
AlexW
Member
Registered: 25th Oct 08
Location: Essex
User status: Offline
|
Pulled the plugs out? They will tell you a lot.
|
X16joeXE
Member
Registered: 26th Jul 09
Location: Tarvin, Cheshire
User status: Offline
|
Mine did this when my cat was blocked.
|
silvertornado
Member
Registered: 9th Oct 09
Location: nottingham NG5 (east mids)
User status: Offline
|
car is decat so no issues with cat being a problem will check plug in morning any other ideas than that ?
|
c20xecorsa
Member
Registered: 8th May 09
Location: Hebburn, Tyne and Wear
User status: Offline
|
U just rebuilt the engine
|
DaveyLC
Member
Registered: 8th Oct 08
Location: Berkshire
User status: Offline
|
Running lean?
|
silvertornado
Member
Registered: 9th Oct 09
Location: nottingham NG5 (east mids)
User status: Offline
|
I dunno am unsure about running lean and its not been rebuilt recent to my knowing
|
andyc1234
Member
Registered: 7th Nov 06
Location: Lancashire
User status: Offline
|
normally timing retarded that would make it glow is it being limited a 4k revs by any chance
|
silvertornado
Member
Registered: 9th Oct 09
Location: nottingham NG5 (east mids)
User status: Offline
|
nope will rev all the way to limiter just can't work out problem fitting an egr now to see if makes a difference
|
andyc1234
Member
Registered: 7th Nov 06
Location: Lancashire
User status: Offline
|
doubt it will be the egr. do the paperclip test and save the hassle
|
silvertornado
Member
Registered: 9th Oct 09
Location: nottingham NG5 (east mids)
User status: Offline
|
paper clip test = 1405 which is egr :S spark plugs removed to find like a white crystal build up :S help
|
andyc1234
Member
Registered: 7th Nov 06
Location: Lancashire
User status: Offline
|
is that the only thing that came up?
|
silvertornado
Member
Registered: 9th Oct 09
Location: nottingham NG5 (east mids)
User status: Offline
|
yep which is now sorted now have no eml but car still running lumpy with with not take revs
|
silvertornado
Member
Registered: 9th Oct 09
Location: nottingham NG5 (east mids)
User status: Offline
|
HELP????
|
Root
Member
Registered: 28th Dec 08
User status: Offline
|
mate, do a paperclip test.
|
silvertornado
Member
Registered: 9th Oct 09
Location: nottingham NG5 (east mids)
User status: Offline
|
quote: Originally posted by Root
mate, do a paperclip test.
read above paper clip test = 1405 which is egr which is now sorted and gives NO eml :S
|
Root
Member
Registered: 28th Dec 08
User status: Offline
|
oh ok. god knows
|
andyc1234
Member
Registered: 7th Nov 06
Location: Lancashire
User status: Offline
|
double check you cambelt timing fella somethings wrong somewere. if you can get hold of one maybe try a different crank sensor on it. also check your bottom pulley that the sensor runs off make sure its not stripped the keyway on it
|
silvertornado
Member
Registered: 9th Oct 09
Location: nottingham NG5 (east mids)
User status: Offline
|
key on bottem pully seams ok might try crank sencer just found out that the lambda might not be working cus if you un plug it theres no eml :S
|
silvertornado
Member
Registered: 9th Oct 09
Location: nottingham NG5 (east mids)
User status: Offline
|
lamda replaced and re sealed all the inlet side of things and still getting glowing manifold and is now back popping in the inlet also have replaced crank senser
any help please???
[Edited on 04-03-2010 by silvertornado]
|