jpearce
Member
Registered: 25th Oct 06
Location: plymouth
User status: Offline
|
Decided to break my corsa as im looking to go RWD
All prices DO NOT include postage but i can post pretty much any item, average items upto 25kg will cost £10, worst case i will pallet the engine up to send too. (delivery on pallet is normaly £50-£80)
Located in Plymouth Devon.
I have pictures on my phone but cant find the lead atm so will have all the pics uploaded over the next day or two. Any specific pics of anything please ask
The car is using still being used daily so i wont be stripping it untill i have sold the engine. So once a deposit has been taken on the engine i will have the car stripped right down over one week and have all the parts ready to go out.
X18XE1 1.8 16v small block engine conversion. £550
This includes everything needed to fit into your corsa b.
includes:
X18XE1 with all sensors/ecu/chip/transponder
F15 (think its close ratio)
x14xe flat flywheel (much lighter than the 1.6 pot flywheel)
AP uprated clutch
modified downpipe with cat (to bolt straight to a corsa system)
corsa b engine mounts (rubbers have been filled so they are more firm)
custom made wiring loom (plugs straight into corsa dash loom)
Custom Inlet using 2.5 inch silicon/alloy tubing.
Fuel tank lid with FPR and Y piece (as these engines run 1fuel line and FPR tank)
Starter/alternator
modified gear linkage
When i bought the engine it was removed from a 92k Vectra B, which ran perfect.
before fitting i fully stripped the engine down and have had the head mildy ported/polished and matched to the inlet.
Every single gasket and seal has been replaced with new genuine/elring gaskets.
New genuine GM cambelt kit and water pump.
and allways been run on GM 10w40 oil.
Since fitting it has done less than 10k miles and never had a problem except the dodgy ecu which has been replaced.
Will include some spares inc ECU kit (works fine just idles high) and soome various sensors.
Runs very well and certainly goes very well in the corsa even in standard form.
These are 115bhp standard and respond well to tuning.
Im looking at £500 no offers.
this is everything you need to convert your corsa to a X18XE1 and has certainly cost me a lot more than than to build/fit.
Lexmaul X18XE1 Syainless 4-2-1 Exhaust manifold, will also fit Z18xe and give at least 10hp on either engine. designed for the astra mk4 but will fit any of these engines with slight adaption to the exhaust system. £300
set of four caviler slab alloys.
Bought these off a friends vaux breakers, they were in perfect condition with no kurbing to them at all.
Ive had them sand blasted and powder coated in anthracite so look mint.
FItted with 4 Yokohama Parada spec 2 tyres 195/50/15. Rears are almost like new fronts are getting low, aprox 3mm left on them. (as im still driving the car it wouldnt suprise me if the fronts will be illegal so keep this in mind)
the wheels are literaly as they came from the powder coaters so mint
With all 4 centra caps but these are still orginal silver so idealy needs painting in anthracite to match the wheels.
cost me the following
Slabs £60
sandblasting and powder coating £180 (through a friend)
tires £150
so in all cost me well over £300
Ill take £200 for them
Exhaust system, think its stainless (need to check) looks slightly larger bore than standard. with 2.5" outward rolled tip £60
FK Highsport coilovers, Comes with FK adjustable rear springs and Jamex rear shocks. in good condition, has some usual corrosion but does not affect them. car drives pretty well with these on. new top mounts fitted when conversion done aprox 10k ago £100
big front brake kit. consists of vectra gsi 288mm front calipers, 280mm Meriva 4stud discs and new pads. done less than 10k on them so plenty of life left in them £60
Front poly bushes. RED firmer bushes, were fittted to new wishbones. with tie bars and brackets (so TCA bushes and Tie bar bushes with bottom ball joints (done less than 10k) ready to fit £40
Goodridge Braided Brake lines, Brand new never used/fitted £30
Carbon Fibre door cards, front and rear. one front has a 1inch scratch otherwise pretty damn good condition. set of 4 so includes rears too £70
Carbon Fibre sunroof panel (goes over the hole if you are removing the sun roof. In mint condition £70
Fibre glass inner front wheel arch covers (sits inside engine bay) £30
Quick rack, 2.7 turns lock to lock £40
Electric sunroof conversion £20
GSi spoiler genuine £20
Irmscher CDX rear bumper £50
NEW OMP rear strut brace £30
RARE SPARCO Alloy front strut brace. polished alloy. adjustable length and height so should fit most engined corsa b's £50
OMP 10 point bolt in roll cage. the plates have been cut off as this was going to be shortened to fit properly in a sun roof equiped corsa while keeping the sun roof. will need painting still. includes door bars/front section. £250
Chrome interior door handles £10
130mph clocks with rec counter and tigra surround fitted. electric. around 105-110k £15
140mph clocks with rev counter. mechanical £15
Short gearstick with irmscher titianium insert in std gearknob (feels much better than std) £20
Late spec Black dash board £15
Pair of Headlights £15
Corsa anti slip Dash Matt £5
Tigra scuttle panel in V good condition £10
There will be some more bits and pieces i will add as and when come across them. any other bits not listed please ask. all panels ect available too
P reg corsa sport 1.4 16v Shell. complete front end (doors forward) has been stitch welded and has had the cross member strengthening plates fitted. at least 6months MOT. will include rear axle, doors/wings/bonnet, wiring loom and some other bits n pieces. £50 (would be nice to sell as a rolling shell with some of the above parts. (will have to be collected from just outside of Plymouth)
|
fazza
Member
Registered: 7th Feb 08
Location: Plymouth
User status: Offline
|
Pearce i will take the tigra scuttle mate.
pm me a price for the doorcards...
|
fazza
Member
Registered: 7th Feb 08
Location: Plymouth
User status: Offline
|
Pearce also interested in the front brakes, you got the wind deflectors still?
|
jpearce
Member
Registered: 25th Oct 06
Location: plymouth
User status: Offline
|
lol its CK....
make an offer...
seamus is having the following:
2.5" SS system
wind deflectors
headlight protectors
anti dive kit
silicon rad hoses
|
fazza
Member
Registered: 7th Feb 08
Location: Plymouth
User status: Offline
|
got all the others, he want any bits off my nova?
definately want the scuttle, wheres the car ck?
|
fazza
Member
Registered: 7th Feb 08
Location: Plymouth
User status: Offline
|
has it got pas mate?
|
jpearce
Member
Registered: 25th Oct 06
Location: plymouth
User status: Offline
|
its outside my house hes here now, i just wrote this up for him.
obv the car wont be stripped untill the engine has been sold/deposit paid as the car is still being used daily,
Pearce said stop spamming his thread lol, and said ring him you skivy cunt lmfao
Non power steering quick rack on it..
[Edited on 05-09-2010 by jpearce]
|
LeeHadfield
Member
Registered: 27th Jan 09
Location: Mansfield, Notts
User status: Offline
|
dibs on passenger side front wing posted?
|
J200RSA
Member
Registered: 23rd May 05
Location: Sheffield
User status: Offline
|
ill take door cards if still available
|
matty101
Member
Registered: 21st Apr 10
Location: Hexham, Northumberland
User status: Offline
|
u2u'd
|
baxter123
Member
Registered: 4th Jul 10
Location: Luton
User status: Offline
|
got a pick of the rear strut brace? interrested
|
jpearce
Member
Registered: 25th Oct 06
Location: plymouth
User status: Offline
|
Bump want it gone
|
Fusion@Selectdjs.co.uk
Member
Registered: 2nd May 10
Location: Eastbourne East sussex
User status: Offline
|
Are you selling any body panels mate?
|
jpearce
Member
Registered: 25th Oct 06
Location: plymouth
User status: Offline
|
The door cards are avaliable mate txt me on 07875334880 I cant read any u2us for sum reason so if any one wants to get hold of me please text and no id rather sell the shell than start taking pannels off bud not worth the hassel what was it you was after anyway?
|
Saloon
Member
Registered: 29th Jan 10
Location: Avonmouth, Bristol
User status: Offline
|
Pics of the engine?
|
Fusion@Selectdjs.co.uk
Member
Registered: 2nd May 10
Location: Eastbourne East sussex
User status: Offline
|
I want both doors and both wings
|
jpearce
Member
Registered: 25th Oct 06
Location: plymouth
User status: Offline
|
Il get pics of engine 2morrow mate
|
matty101
Member
Registered: 21st Apr 10
Location: Hexham, Northumberland
User status: Offline
|
dont forget to post the dash mat tomorrow mate
|
spankyjames
Member
Registered: 26th Jun 06
Location: Corsham, Wiltshire
User status: Offline
|
really want the cdx rear bumper and front breaks and braided hoses, will get back to you
|
jpearce
Member
Registered: 25th Oct 06
Location: plymouth
User status: Offline
|
okay james mate text me if you want
|
spankyjames
Member
Registered: 26th Jun 06
Location: Corsham, Wiltshire
User status: Offline
|
whats best price on all of the bits i want
|
SEAN_P_
Member
Registered: 30th Nov 09
Location: *Washington*North-East*
User status: Offline
|
Hi mate could you send me a u2u I want to ask you a few thinks. I can u2u u bak I am just on my fone thats all
|
ckallis500
Member
Registered: 14th Dec 04
Location: plymouth
User status: Offline
|
All panels can be sold but not untill the engine sells as the car is stripped, as said it is used daily so most bits wont be sold untill engine goes. Can post pretty much anything too inc doors/wings ect
any specific pics please ask
Some pics
|
Stu_22
Member
Registered: 25th Mar 02
Location: Luton
User status: Offline
|
Manifold wont fit a Z18XE with an oil level sensor as I have found
|
spikefrost17
Member
Registered: 13th Sep 10
Location: exeter, devon
User status: Offline
|
hi friend, i'm interested in the engine + conversion package, can you pm me your phone number so i can arrange to come look at it? i'm only over the border in devon, so not too far to travel cheers!
|