BeetleGav
Member
Registered: 27th Jun 10
Location: lancashire, nelson
User status: Offline
|
What would i need to get hold of? and howmuch am i looking at to spend?
cheers people, im not clued up at all
|
Welly Wanger
Member
Registered: 5th Jan 12
Location: Cambodia stroke Yorkshire
User status: Offline
|
i know nowt about corsa's but wouldnt this be easier? http://www.corsasport.co.uk/board/viewthread.php?tid=628782
|
BeetleGav
Member
Registered: 27th Jun 10
Location: lancashire, nelson
User status: Offline
|
no because my car is mint. it has 23k on the clock. just needs a bigger engine
|
Alex_Rally
Member
Registered: 6th Sep 09
Location: Tyne and Wear, gateshead
User status: Offline
|
engine
ecu transponder chip
depending on what engine is in atm. mounts
loom
brakes
shafts
|
tom130691
Premium Member
Registered: 13th Sep 08
Location: Daventry
User status: Offline
|
quote: Originally posted by BeetleGav
no because my car is mint. it has 23k on the clock. just needs a bigger engine
be a shame to put an engine with more miles in it
but as far as i am aware 1.0 are annoying to covert to anything, shaun managed it though
|
BeetleGav
Member
Registered: 27th Jun 10
Location: lancashire, nelson
User status: Offline
|
quote: Originally posted by tom130691
quote: Originally posted by BeetleGav
no because my car is mint. it has 23k on the clock. just needs a bigger engine
be a shame to put an engine with more miles in it
but as far as i am aware 1.0 are annoying to covert to anything, shaun managed it though
well im hoping to get an engine with low miles. my car will have about 30k on it by the time i convert it. did 10k lastyear. hope it aint hard to change
the hairdryer in question
|
Alex_Rally
Member
Registered: 6th Sep 09
Location: Tyne and Wear, gateshead
User status: Offline
|
get the engine rebuilt then if you dont wanna put a hi miler in mate
|
BeetleGav
Member
Registered: 27th Jun 10
Location: lancashire, nelson
User status: Offline
|
yeah thats true, would i need to change gearbox or anything like that?
|
fazza
Member
Registered: 7th Feb 08
Location: Plymouth
User status: Offline
|
Ive been doing some searching, and you need to change the entire dash loom before you can fit the different engine.
|
BeetleGav
Member
Registered: 27th Jun 10
Location: lancashire, nelson
User status: Offline
|
ah thats crap! might have to stay like this then until i can afford a new car :\
was hoping it would be relatively simple
|
Linch
Member
Registered: 4th May 06
Location: Whickham, Tyne and Wear
User status: Offline
|
quote: Originally posted by fazza
Ive been doing some searching, and you need to change the entire dash loom before you can fit the different engine.
This is wrong. No you dont. You need to pull the ecu wires from inside the bay back into the car. Easy.
|
GB123
Premium Member
Registered: 21st Nov 11
Location: Kent
User status: Offline
|
1.0's are the hardest to do conversions on because most stuff seems to be different.
|
fazza
Member
Registered: 7th Feb 08
Location: Plymouth
User status: Offline
|
Really?
so if you cut the ECU plug off from the engine bay, you will be left with the same wires as any other model?
Green - revs
Thick blue/red - fuel
etc?
|
Jed D
Member
Registered: 15th Mar 11
Location: Durham
User status: Offline
|
buy a 1600 lump and rebuild it whilst still using the 12volt...
...or buy a corsa/tigra/astra and make some money back scrapping the shell and selling unneeded bits
astras and some vectras came with the x16xeL wich has a better head i believe but uses different management i think... and they tend not to of been as ragged as the corsas/tigra's
[Edited on 04-03-2012 by Jed D]
|
Linch
Member
Registered: 4th May 06
Location: Whickham, Tyne and Wear
User status: Offline
|
http://www.corsasport.co.uk/board/viewthread.php?tid=611430
|
Linch
Member
Registered: 4th May 06
Location: Whickham, Tyne and Wear
User status: Offline
|
quote: Originally posted by fazza
Really?
so if you cut the ECU plug off from the engine bay, you will be left with the same wires as any other model?
Green - revs
Thick blue/red - fuel
etc?
Yes, A few are different and unused ect so just need taped up.
|
corsa-vxr
Member
Registered: 15th Apr 11
Location: ayr
User status: Offline
|
you just pull the wires back through into the cabin from a 1.0 wirings the same its just the relay under glove box that needs dealt with wiring is here for 1.0 and 1.2 16v to c20xe c20let etc
http://www.corsasport.co.uk/board/viewthread.php?tid=611430&highlight=1&pid=8036832#pid8036832
|
Crana
Member
Registered: 20th Jan 09
Location: Newcastle
User status: Offline
|
1.2 16v and 12v shell are just as easy to convert just take a little bit longer because you have to pull the wires back in the car like linch said, I has a 23k minter like yours and got board of the 60bhp on raw power so put a eco-shite in and it was the worst thing I ever done I wasn't happy with the power or oil consumption at all wish I had just put a 20xe in now
|
BeetleGav
Member
Registered: 27th Jun 10
Location: lancashire, nelson
User status: Offline
|
howmuch would i be looking at to do either a 20xe or 1.6? id need someone to help me do it because i wouldnt know where to start. especially with wiring.
|
Linch
Member
Registered: 4th May 06
Location: Whickham, Tyne and Wear
User status: Offline
|
xe conversion now are about £500 all in. 1.6 youd be looking at maybe £300 for a good engine.
|
redtom
Member
Registered: 6th Oct 07
Location: Kent
User status: Offline
|
Conversion is just as easy just have to pull the wires through and bridge the relay as linch said. People make it sound so much more hassle then it actually is
|
BeetleGav
Member
Registered: 27th Jun 10
Location: lancashire, nelson
User status: Offline
|
quote: Originally posted by Linch
xe conversion now are about £500 all in. 1.6 youd be looking at maybe £300 for a good engine.
thats not too bad, would i not need a different gearbox for an xe? or are they all the same?
|
GB123
Premium Member
Registered: 21st Nov 11
Location: Kent
User status: Offline
|
quote: Originally posted by BeetleGav
quote: Originally posted by Linch
xe conversion now are about £500 all in. 1.6 youd be looking at maybe £300 for a good engine.
thats not too bad, would i not need a different gearbox for an xe? or are they all the same?
Yeah you will need either a f20, f16 or an f28.
|
BeetleGav
Member
Registered: 27th Jun 10
Location: lancashire, nelson
User status: Offline
|
ahrite, cheers.
|
Linch
Member
Registered: 4th May 06
Location: Whickham, Tyne and Wear
User status: Offline
|
or f18
|