grimmy
Member
Registered: 1st Jul 08
Location: Scottish Borders
User status: Offline
|
where should the black wire coming off the end of the fuel rail get connected too?
|
B3KAN
Member
Registered: 15th Feb 07
Location: Inverness, Highland
User status: Offline
|
Ignition live, you need to run a wire from inside the car where both looms get joined, its the thin black wire on the car loom
|
grimmy
Member
Registered: 1st Jul 08
Location: Scottish Borders
User status: Offline
|
does this black wire turn too brown wire inside the black case full of wires? as both wires coming out the right hand end of the fuel rail are brown, is there only ment to be one earth?
|
lee mitchell
Member
Registered: 26th Jan 01
Location: kent...drive's: eveyones conversion cars hard lol
User status: Offline
|
no theyre both earths
|
Ste
Premium Member
Registered: 5th Mar 03
Location: Taif, Saudi Arabia
User status: Offline
|
Have you read the tutorials before posting?
I would rather lose by a mile because i built my own car, than win by an inch because someone else built it for me.
|
grimmy
Member
Registered: 1st Jul 08
Location: Scottish Borders
User status: Offline
|
yes, but just can't find this black wire from the fuel rail everyone talks about.
|
grimmy
Member
Registered: 1st Jul 08
Location: Scottish Borders
User status: Offline
|
is it one of these wires you have to join into?
|
redtom
Member
Registered: 6th Oct 07
Location: Kent
User status: Offline
|
they are bioth earths. go from there and go along the loom towards the coil. there should be a single black wire somwhere along the line assuming its not missing.
|
grimmy
Member
Registered: 1st Jul 08
Location: Scottish Borders
User status: Offline
|
there is a green wire with a blck cover and conector on the end
|
grimmy
Member
Registered: 1st Jul 08
Location: Scottish Borders
User status: Offline
|
anyone got a picture of this wire?
|
grimmy
Member
Registered: 1st Jul 08
Location: Scottish Borders
User status: Offline
|
i don't have any plugs on mine so i've opened up the loom coming from the fuel rail and someone's alredy been into it.
there are 4 black wires in total, the thick one goes to sensor on distributor, then there is 3 more but 1 has been soldered for sumreason?
in the footwell is the black wire to be connected for switched live the one beside the green wire in picture below? if so when i had the tester on the black wire from footwell is connected to the wires that are soldered in the engine bay.
also in the picture above what is the little connector for that isn't plugged in for, an in the picture below for sum reason there is a thin red wire been added to the blue/red wire for the fuel pump relay why would this have been done an what happens with the plug that is coming off the fuel pump realy?
sorry for the essay but am bit stuck with this now, the engine is turning over an there is petrol and spark so it's just this wiring im stuck with. but looks like the loom has been played with anyway thats why i've got problems.
|
redtom
Member
Registered: 6th Oct 07
Location: Kent
User status: Offline
|
where does the soldered one go? that looks like the right sort of wire for the switched live. its always best to start with a completely untouched loom tbh.
|
grimmy
Member
Registered: 1st Jul 08
Location: Scottish Borders
User status: Offline
|
it's already getting power too it the one thats soldered? the engine and loom was bought and it was supposed too be ready just too drop in, but it's took sum sorting with all the bodging on it.
wot is it that this switched live is for? would the car run without it connected?
|
redtom
Member
Registered: 6th Oct 07
Location: Kent
User status: Offline
|
car wouldnt run without it. are you getting an emlight on the dash? it needs to be connected to a wire which needs to be run back into the car and connected to the black wire inside the car by the ecu.
|
grimmy
Member
Registered: 1st Jul 08
Location: Scottish Borders
User status: Offline
|
is that the black wire in that bunch beside the green infront of the thick red one thats just pulled away a bit?(sorry about bad pic) theres no em light on but all others are coming on
|
redtom
Member
Registered: 6th Oct 07
Location: Kent
User status: Offline
|
could be cant really tell. if the bunch of wires are coming from up behind the dash and the wires in the bunch with it are the ones used in the conversion then yes its that one.
if there is no eml then its either not connected properly or double check the bulb works.
|
grimmy
Member
Registered: 1st Jul 08
Location: Scottish Borders
User status: Offline
|
car is now sorted an running finally lol, thanks for the help
|
redtom
Member
Registered: 6th Oct 07
Location: Kent
User status: Offline
|
what was up with it mate?
|
grimmy
Member
Registered: 1st Jul 08
Location: Scottish Borders
User status: Offline
|
just a bit of re-wiring needed doing
|