SAL
Premium Member
Registered: 19th Dec 05
Location: Radlett, Hertfordshire
User status: Offline
|
iv allready got a lexmaul ram induction and a stainless stystem. looking for more power, maybe a re map? iv try a decat but the car sounds like a fast tractor! 
|
Rob B
Member
Registered: 8th Jan 04
Location: Area Motorsport Drives: Race EP3
User status: Offline
|
de-cat, some form of ram air like a viper, manifold, remap..
|
SAL
Premium Member
Registered: 19th Dec 05
Location: Radlett, Hertfordshire
User status: Offline
|
iv got a dblias air flow kit on the way (like a viper) the de cat made the car toooo loud, which might be a problem with a manifold?do they make the exzorst note alot louder?
|
Dean_W
Member
Registered: 13th Dec 05
Location: Downham Market, Norfolk
User status: Offline
|
MY de-cat made no difference to sound, but i do still have the middle box.
|
Butler
Member
Registered: 2nd Jun 05
Location: London
User status: Offline
|
decat, manifold, cams, induction, then a remap
|
jazzer2k3
Member
Registered: 24th May 03
Location: **SHEFFIELD**
User status: Offline
|
I got dbilas inlet, magnex exhaust inc de-cat ... dont want cams cos ur car wont benefit from them unless u get proper verniers . . . .
Im gettin a remap with a raised limiter - (Corsa GSi) But atm its fast enough 
|
SAL
Premium Member
Registered: 19th Dec 05
Location: Radlett, Hertfordshire
User status: Offline
|
how much is a remap? is dblias software a chip or re map?
|
Robin
Premium Member
Registered: 7th Jan 04
Location: Northants Drives: Clio 182 Cup
User status: Offline
|
Dbilas Vernier pullies, so you can keep the standard ECU, cams, decat and get the ECU chipped and mapped (wont be cheap, but will be worth it, but only do it when you've got EVERYTHING on, or it'll need doing again)
then some headwork and you should see 145-150bhp
|
Fad
Member
Registered: 1st Feb 01
Location: Dartford Kent Drives: 330cd
User status: Offline
|
you have a decnt inlet and its a shame you spanked that money on the airflow thingy maaa jiggy as that would of paid for the headwork rob mentioned.
If i had a 1.6 and wasnt going down the tb rout i would have this spec:
Lexmaul inlet
Kent 264 cams
Vernier pulleys
flowed and ported head
uprated valve springs and caps (as head would be off anyway)
ARP rod bolts
Drilled air box
fll stainless steel echaust and decat
janspeed exhuaust manifold
lightend flywheel and uprated clutch
Then either look into a unichip of best of all aftermarket management as the inlet benefits from a higher rev limit
most of what I have listed above can be done quite cheaply if you keep an eye on both the classified here and on MIGweb
[Edited on 08-08-2006 by Fad]
|
jazzer2k3
Member
Registered: 24th May 03
Location: **SHEFFIELD**
User status: Offline
|
Hey Fad, the verniers u used made the cams make a noticable difference ???
|
Fad
Member
Registered: 1st Feb 01
Location: Dartford Kent Drives: 330cd
User status: Offline
|
quote:
Originally posted by jazzer2k3
Hey Fad, the verniers u used made the cams make a noticable difference ???
I never went this far with tunning my x14xe but if i did i would do verniers as they make it easier to set up due to timing marks etc and they are shit loads lighter than standard pulleys
|
jazzer2k3
Member
Registered: 24th May 03
Location: **SHEFFIELD**
User status: Offline
|
Ye i know, it's jus i was sooo close on puttin cams into my gsi...and alos was biddin on some vernier's .. but then got told that there are no verniers to fit the x16xe ! ? Dunno lol
|
Robin
Premium Member
Registered: 7th Jan 04
Location: Northants Drives: Clio 182 Cup
User status: Offline
|
Dbilas Verniers do, they are the ONLY ones which will work with the standard ECU/Sensor set up
well worth it, you can do a lot with a little of adjustment
|
jazzer2k3
Member
Registered: 24th May 03
Location: **SHEFFIELD**
User status: Offline
|
well standard ECU meaning a totally standard ? Cos it's goin to have been chipped (not a 10p resistor from ebay) a datek (i think) with raised limiter ... Will still be able to get these verniers to work with that ECU ?
|
Robin
Premium Member
Registered: 7th Jan 04
Location: Northants Drives: Clio 182 Cup
User status: Offline
|
yeah, i mean a standard ECU as far as the sensor setup goes.
you cant run piper/kent verniers with a standard sensor setup, as it has a cam sensor.
the Dbilas Verniers have the bits to work with the cam sensor
|
jr
Member
Registered: 20th May 02
Location: Kent
User status: Offline
|
But the nice janspeed manifold i have thats only done 1k
|
K11 NNL
Member
Registered: 25th Jan 05
Location: Fife
User status: Offline
|
a had a mantzel inlet,dbilas,intake,4 branch,de cat,full stainless and got 144bhp,put cams and dbilas pulleys on and got 145bhp they dont benefit much at all because the engine is already such a high compression that the valves are so close to the pistons so you cant get the proper adjustment you need.mines had a very poor pick up but kept power all the way to the limiter.wouldnt recommend cams imo.
|
Fad
Member
Registered: 1st Feb 01
Location: Dartford Kent Drives: 330cd
User status: Offline
|
depends on the profile of cams and I can tell you 264's are definately notable espeically at 5k revs and at idle
|
jr
Member
Registered: 20th May 02
Location: Kent
User status: Offline
|
|
K11 NNL
Member
Registered: 25th Jan 05
Location: Fife
User status: Offline
|
aye at idle mine sounded like a subaru and picked up at 5k but was very poor below that.
|
