Jonny.N
Member
Registered: 10th Sep 08
Location: scotland
User status: Offline
|
could someone write a list of what i need? and it has epas aswell if thats any use? dont wanna go down the route of taking the dash out to change to normal pas setup, ideally wanna make the epas work with the 1.6 16v if its possible? thanks
|
shaunmods
Premium Member
Registered: 12th Mar 07
Location: Glascote, Staffordshire
User status: Offline
|
http://www.corsasport.co.uk/board/viewthread.php?tid=601754
|
Jonny.N
Member
Registered: 10th Sep 08
Location: scotland
User status: Offline
|
thanks
|
Jonny.N
Member
Registered: 10th Sep 08
Location: scotland
User status: Offline
|
how does that work with epas?
|
shaunmods
Premium Member
Registered: 12th Mar 07
Location: Glascote, Staffordshire
User status: Offline
|
you need to convert the aux belt setup to one from an early corsa 1.4 16v sri so that you can run it without the 1.6 PAS pump. Its all explained in the tutorial in the link above 
|
Jonny.N
Member
Registered: 10th Sep 08
Location: scotland
User status: Offline
|
yeah i seen that, but how do i go about wiring in the epas is what i ment to put 
|
shaunmods
Premium Member
Registered: 12th Mar 07
Location: Glascote, Staffordshire
User status: Offline
|
quote:
Originally posted by Jonny.N
yeah i seen that, but how do i go about wiring in the epas is what i ment to put
Shouldnt need to touch the wiring for the EPAS mate. You'll just have to extend the dash loom wiring over to the driver side footwell for the ECU as the loom comes out in a different place in the engine bay on the 1.2 16v's
|
AlexW
Member
Registered: 25th Oct 08
Location: Essex
User status: Offline
|
Your have fun with EPAS as changing the dash loom means the fusebox is in the way of the EPAS motor, plus it needs wiring in, as the factory wiring will be part of the dash loom.
Ditch the EPAS and go for fluid pas.
[Edited on 27-04-2011 by AW06]
|
shaunmods
Premium Member
Registered: 12th Mar 07
Location: Glascote, Staffordshire
User status: Offline
|
quote:
Originally posted by AW06
Your have fun with EPAS as changing the dash loom means the fusebox is in the way of the EPAS motor, plus it needs wiring in, as the factory wiring will be part of the dash loom.
Ditch the EPAS and go for fluid pas.
He doesnt want to change the dash loom you tit 
|
AlexW
Member
Registered: 25th Oct 08
Location: Essex
User status: Offline
|
Meh didnt read that bit. If your rewiring all the ecu plug then yes, it will be fine, But I just wouldn't do it that way as its not perfect 
|
Jonny.N
Member
Registered: 10th Sep 08
Location: scotland
User status: Offline
|
i just dont wanna go through the hassle of taking the dash out to swap looms and pas setup etc again, as i did that with my last one a month ago and gave up with it , trying to do it in a way i dont need to swap anything interior wise ideally, so anyone any ideas how to and where to wire epas in? a autospark should be able to do it no probz?
|
Jonny.N
Member
Registered: 10th Sep 08
Location: scotland
User status: Offline
|
quote:
Originally posted by shaunmods
quote:
Originally posted by Jonny.N
yeah i seen that, but how do i go about wiring in the epas is what i ment to put
Shouldnt need to touch the wiring for the EPAS mate. You'll just have to extend the dash loom wiring over to the driver side footwell for the ECU as the loom comes out in a different place in the engine bay on the 1.2 16v's
yeah extending the wires etc isnt the problem, when i disconnect the epas from the ecu, theres a red and grey( i think) cable sitting there, surely thats to power it? its where that would get connected to,
|
Jonny.N
Member
Registered: 10th Sep 08
Location: scotland
User status: Offline
|
any1?
|
