Jed D
Member
Registered: 15th Mar 11
Location: Durham
User status: Offline
|
easy to remove?
i know about the two screws in the top that hold the MFD in but what else is there to it?
also the cylinder shaped bit on the passenger side of the dash (like were the passenger air bag would be)
cheers 
[Edited on 29-02-2012 by Jed D]
|
Ian
Site Administrator
Registered: 28th Aug 99
Location: Liverpool
User status: Online
|
Two behind the heater slider as well.
|
Jed D
Member
Registered: 15th Mar 11
Location: Durham
User status: Offline
|
and thats it? cheers 
|
Ian
Site Administrator
Registered: 28th Aug 99
Location: Liverpool
User status: Online
|
Yeah for that panel.
Cylinder shaped thing has three screws underneath, need the glove box out first, that is two inside at the front, two underneath and one inside at the back.
|
Jed D
Member
Registered: 15th Mar 11
Location: Durham
User status: Offline
|
spotty dog ian
|
Bmorgan1993
Member
Registered: 28th Sep 11
Location: Gloucester, Gloucestershire
User status: Offline
|
Just to add on to one Ian said if you havn't done it before (which i'm presuming) take your time putting it back in as its a difficult first time round IMO.
|
Jed D
Member
Registered: 15th Mar 11
Location: Durham
User status: Offline
|
iv done it many times in other cars and iv had the mfd out in the corsa before but never had reason to have it all out
|
Jed D
Member
Registered: 15th Mar 11
Location: Durham
User status: Offline
|
got the centre bit out... what a fiddly chew on it is haha... smoothed down and 1st coat of prime... now for the cylinder shaped bit on the passenger side..
|
Phoenix Autosport
Member
Registered: 9th Oct 11
Location: Cambs / Northants
User status: Offline
|
reading through this i couldnt see a mention of the screw in the end of the cylinder piece, you need to remove the passenger side air vent to get at it, and when removing the glovebox if its the larger version remember the screw inside in theglovebox in the middle near the back, i always forget that one and wonder why the thing wont come out 
|
Jed D
Member
Registered: 15th Mar 11
Location: Durham
User status: Offline
|
aye, cheers for that, though id seen a scre on the outer edge in someone thread before, just in the nick of time as im about to go out and remove it haha cheers
mines the smaller glove box as it HAD a/c... what would i need to do to fit the bigger glove box other than get the glove box obviously?
its just in the next few days im going to be removing whatever A/C things that are left as a non A/C screenwash bottle (one that goes under the scuttle) will be going in... try kill two birds with one stone...
|
Phoenix Autosport
Member
Registered: 9th Oct 11
Location: Cambs / Northants
User status: Offline
|
im pretty sure you would need to change the heater setup behind the dash for a non aircon version to get the larger glovebox in as the reason for a smaller one was to make room for the aircon components
|
Jed D
Member
Registered: 15th Mar 11
Location: Durham
User status: Offline
|
See what you mean now i have the glovebox out
How many screws are holding that end vent in?? Iv got two out, 1. at the bottom 2. inside the vent
|
Phoenix Autosport
Member
Registered: 9th Oct 11
Location: Cambs / Northants
User status: Offline
|
thats it for the screws on the vent but it does push into the vent pipe behind the dash and they tend to be a tight fit, give it a good pull and a wiggle and it will come off
|
Jed D
Member
Registered: 15th Mar 11
Location: Durham
User status: Offline
|
ok, cheers, didnt want to break it. so your sure theres nothing from the side of the dash holing it in then?
|
Phoenix Autosport
Member
Registered: 9th Oct 11
Location: Cambs / Northants
User status: Offline
|
nope only fixing in the side should be a torx that is one of the dashboard fixings
|
Jed D
Member
Registered: 15th Mar 11
Location: Durham
User status: Offline
|
x2 torx and a random one that had a plastic bit covering it... (top)
|
Phoenix Autosport
Member
Registered: 9th Oct 11
Location: Cambs / Northants
User status: Offline
|
top bit on the ones i have stripped for parts at the breakers either have a plastic bung in or just a hole but i have never worked out what its for, vent on passenger side definately only has 3 fixings, two up top inside vent and one underneath where glovebox fits
you can see the lower one in this image
/corsa_b_side_vents_black.jpg)
|
Jed D
Member
Registered: 15th Mar 11
Location: Durham
User status: Offline
|
ahhh two up the top... lol, i thought only one  doh
cheers... will have another bash tomorrow... centres on drying as we speak 
thanks for your help
|
Phoenix Autosport
Member
Registered: 9th Oct 11
Location: Cambs / Northants
User status: Offline
|
no worries, post up some pics when your done, be interesting to see how it looks
|
Jed D
Member
Registered: 15th Mar 11
Location: Durham
User status: Offline
|
will do. this is the bit iv already done...
iv got a small run in the centre console, nothing to worry about as i was going to flat it down again and paint... tomorrows another day lol
|
XE Col
Premium Member
Registered: 23rd May 10
Location: Rochdale, AKA:Boissy07
User status: Offline
|
What's them rings on the clocks jed?
|
Jed D
Member
Registered: 15th Mar 11
Location: Durham
User status: Offline
|
quote:
Originally posted by XE Col
What's them rings on the clocks jed?
some sort of chrome rings, normally pick them up on ebay for about £20+ i think, but they came with another set of clocks and i just changed the fronts over
they just glue in on the inside
[Edited on 04-03-2012 by Jed D]
|
