geth_corsa
Member
Registered: 18th May 08
User status: Offline
|
had quite a few problems with fitting this today.
One thing is the cars reving at 4000 rpm, and a huge hissing noise coming from the engine, so i think theres a leak. also the pipe that i recieved with the manifold is doesnt bend, so what can i use?
I dont know if anybody else had this problem, but i had an extremely difficult job in joining the throttle body with the powerbox.
|
barneykarl
Member
Registered: 29th Jul 06
Location: Stevenage
User status: Offline
|
What power box ,sound like you have a bad joint between the throttle body and box ,did you use the gasket and sealer and the three bolts and nut ,double check the throttle to box seal , then box to the rest of inlet seal.
|
Jake
Member
Registered: 24th Jan 05
User status: Offline
|
3 bolts? isnt it held on with 4?
|
geth_corsa
Member
Registered: 18th May 08
User status: Offline
|
the mantzel type off flame.
|
Jake
Member
Registered: 24th Jan 05
User status: Offline
|
press down on the inlet box firmly. might not be a good seal between the inlet and the lower inlet
|
barneykarl
Member
Registered: 29th Jul 06
Location: Stevenage
User status: Offline
|
yes it is 4 but one is a nut and you have to open up the casting a bit on the throttle body to fit it, what pipe are you talking about? like I said recheck your sealed ok which you can,t be as you have the huge hissing, also use some sealant on the throttle body gasket.
|
geth_corsa
Member
Registered: 18th May 08
User status: Offline
|
the hose between the filter and the throttle body. doesnt flex, so the air filet hits the wing. i need some sort of flexible hose i should imagine
|
Jake
Member
Registered: 24th Jan 05
User status: Offline
|
1.2 8v inlet hose
|
barneykarl
Member
Registered: 29th Jul 06
Location: Stevenage
User status: Offline
|
Like this ?
|
geth_corsa
Member
Registered: 18th May 08
User status: Offline
|
ye thats what i could do with lol
|
barneykarl
Member
Registered: 29th Jul 06
Location: Stevenage
User status: Offline
|
Like jake said you could do this lots of ways, my first attempt was the foil type but was crap.
|
geth_corsa
Member
Registered: 18th May 08
User status: Offline
|
ive had another go this morning. still having difficulty sealing it. Theres a constant whining noise, and it misfires aswell.
|
neilb1
Member
Registered: 7th Jul 08
Location: Lancashire
User status: Offline
|
it might either be pipe down to tb thats what were up with me tigra,the other thing is the gasket between the inlet and the lower inlet manifold i had same probs just got a gasket and selant works a dream
|
john_c20xe
Member
Registered: 10th Feb 08
Location: Eastbourne, EastSussex
User status: Offline
|
get the brake cleaner out!! spray parts of the engine around the throttel body etc! you will find your airleak!
|
john_c20xe
Member
Registered: 10th Feb 08
Location: Eastbourne, EastSussex
User status: Offline
|
have you extended your tps sensor also?
|
geth_corsa
Member
Registered: 18th May 08
User status: Offline
|
fitted it now. goes well. my eml is constantly on though, may be because i havent fitted the air flow meter yet??
|
geth_corsa
Member
Registered: 18th May 08
User status: Offline
|
fitted the air flow meter. still idling on 1000 rpm and the eml constantly on. any ideas??
|
barneykarl
Member
Registered: 29th Jul 06
Location: Stevenage
User status: Offline
|
air flow meter ? you mean the air temp sensor, eml probably egr , find out what code/codes are being flashed up, what engine any pics?
|
geth_corsa
Member
Registered: 18th May 08
User status: Offline
|
x14xe it is. ive connected the brass pipe from the powerbox to the egr blanking plate. theres a slight kink in the pipe though. could that affect things??
|
barneykarl
Member
Registered: 29th Jul 06
Location: Stevenage
User status: Offline
|
Not sure what you mean can you post some pics of what you have done, I think you have gone wrong somewhere are you sure you have connected up the brake servo pipe right,also egr blanking plate has no pipe to it,you have gone wrong or are getting your part names mixed up. should be a bit like this
[Edited on 11-01-2009 by barneykarl]
|
geth_corsa
Member
Registered: 18th May 08
User status: Offline
|
i know the top black pipe on the powerbox goes to the brake servo, but where does the second go to mate??
|
barneykarl
Member
Registered: 29th Jul 06
Location: Stevenage
User status: Offline
|
Middle one goes to map sensor you can see the green connector in the pic above.
|
john_c20xe
Member
Registered: 10th Feb 08
Location: Eastbourne, EastSussex
User status: Offline
|
that copper/brass pipe is so the egr can still be used its not a blanking plate, i have the same brass pipe.
[Edited on 11-01-2009 by john_c20xe]
|
john_c20xe
Member
Registered: 10th Feb 08
Location: Eastbourne, EastSussex
User status: Offline
|
you gettin ure hissing still?
|
Ash_EP3
Member
Registered: 15th May 07
Location: Melksham, Wiltshire
User status: Offline
|
I'm interested to see how this goes my inlet should be arriving within the next couple of days...
|